Hobart #22 Funnel-Shaped Meat Chopper Attachment with Knife and 5 Plates. Hobart 22C/E-FS5PLT STANDARD FEATURES ¦ 11/2 H. For 230/50/1 ¦ 12-20 lbs. Per minute capacity ¦ Ideal for “On Demand” meat chopping for processing fresh, boned meat ¦ Can be fed at a rapid pace with continuous chopping action and no crushing or mashing of the meat ¦ All parts which contact food are easily accessible and readily removable for convenient cleaning without the use of tools OPTIONS? Funnel shaped cylinder ACCESSORIES? #22 Stay-Sharp knife & plates? #22 stuffing tubes SPECIFICATIONS MOTOR: 1 1/2 H. For 230/50/1, four pole, AC induction motor. Single phase is capacitor start-capacitor run type. Three phase is poly-phase, induction type. Motor ventilation is provided through screened openings in the base assuring cool operation. Available in standard electrical specifications shown below. SWITCH: Conveniently mounted at the back of machine (can be changed to front). CORD AND PLUG: A 6 foot, flexible 3 wire cord is furnished with the following plugs: 120/60/1 – NEMA 5-15P; 208-240/60/3 – NEMA L15-20P; 230/50/1 – No Plug; 240/60/1, NEMA 6-15P. TRANSMISSION: Precision made gears and shafts mounted on ball bearings are fully enclosed in the transmission case, packed with a special oil at the factory. Smooth, quiet operation is assured for years of normal operation. The attachment hub has a double seal, designed to exclude meat juices or water from the transmission. Worm speed is 212 r. For 60 Hz, 180 rpm for 50 Hz. CHOPPING END: 4822 has a Hobart protective type chopping end, with cylinder of the spiral-fluted design. FS option has a guarded open bowl type chopping end. A heavy cast aluminum safety guard is supported by vertical posts permanently mounted on the cylinder. The cylinder, worm and adjusting ring are all heavily tinned. A heat-treated steel knife and plate and plastic feed stomper are provided. STAY-SHARP KNIFE & PLATES: The Hobart Stay-Sharp knife & plates are made from an alloy steel that holds its edge longer than standard carbon steel. Stay-Sharp plates also can be resharpened many more times than regular plates. These two features allow a substantial lifetime cost benefit with the Hobart StaySharp plates. FEED PAN: 4822 has a stainless steel feed pan – 191/2″ x 111/2″ x 21/2 inside dimensions. FS option has stainless steel pan – 33″ x 153/4″ x 33/4 inside dimensions. CAPACITY: 4822 will grind 16 lbs. Per minute, first cutting through a 1/8 plate. FS option will grind 20 to 22 lbs. FINISH: Standard finish is stainless steel housing. An attractive stainless steel trim plate is provided at the attachment opening and stainless steel legs, cushioned on the bottom with resilient neoprene rubber, provide clearance to keep the table clean under the chopping unit. STANDARD EQUIPMENT: Includes the working unit with protective type tinned chopping end, stainless steel feed pan, plastic feed stomper, one knife and one plate. The plate has 1/8 diameter holes. ¦ Ideal for “On Demand” meat chopping for processing fresh, boned meat. ¦ Can be fed at a rapid pace with continuous chopping action and no crushing or mashing of the meat. ¦ All parts which contact food are easily accessible and readily removable for convenient cleaning without the use of tools. #22 Stay-Sharp knife & plates. MOTOR : 1 1/2 H. SWITCH : Conveniently mounted at the back of machine (can be changed to front). CORD AND PLUG : A 6 foot, flexible 3 wire cord is furnished with the following plugs: 120/60/1 – NEMA 5-15P; 208-240/60/3 – NEMA L15-20P; 230/50/1 – No Plug; 240/60/1, NEMA 6-15P. TRANSMISSION : Precision made gears and shafts mounted on ball bearings are fully enclosed in the transmission case, packed with a special oil at the factory. CHOPPING END : 4822 has a Hobart protective type chopping end, with cylinder of the spiral-fluted design. STAY-SHARP KNIFE & PLATES : The Hobart Stay-Sharp knife & plates are made from an alloy steel that holds its edge longer than standard carbon steel. FEED PAN : 4822 has a stainless steel feed pan – 191/2″ x 111/2″ x 21/2 inside dimensions. CAPACITY : 4822 will grind 16 lbs. FINISH : Standard finish is stainless steel housing. STANDARD EQUIPMENT : Includes the working unit with protective type tinned chopping end, stainless steel feed pan, plastic feed stomper, one knife and one plate. Sorry, our items are NOT available for pick-up. No additional information at this time. You might also like. Peerless CE131PE Electric Countertop Pizza Oven. Peerless C131P Gas Countertop Pizza Oven with Pizza Stones – 30,000 BTU. Amana RCS10TS Commercial Microwave Oven Medium Volume – 120V, 1000W. Avantco W50 12″ x 20″ Full Size Electric Countertop Food Warmer – 120V, 1200W. This item is in the category “Business & Industrial\Restaurant & Food Service\Commercial Kitchen Equipment\Food Preparation Equipment\Food Preparation Equipment Parts & Accessories\Meat Processing Equipment Parts & Accessories”. The seller is “restauranium” and is located in this country: US. This item can be shipped to United States.
- Brand: Hobart
- MPN: 22C/E-FS5PLT